收藏本站

HSC-ADC-EVALC
EVALUATION BOARD HARDWARE
HSC-ADC-EVALC ADC CAPTURE BOARD
EASY START
Requirements
? HSC-ADC-EVALC ADC capture board, VisualAnalog, 5 V
wall transformer, and USB cable
? High speed ADC evaluation board and ADC data sheet
? Power supply for ADC evaluation board
6.
7.
Once the USB cable is connected to both the computer and
the HSC-ADC-EVALC board, and power is applied, the
USB driver starts to install. The Found New Hardware
Wizard opens and prompts you through the automated
install process.
(Optional) Verify in the Windows device manager that
Analog Devices ADC-HSC-EVALC is listed under the
USB hardware.
?
?
?
?
Analog signal source and appropriate filtering
Low jitter clock source applicable for specific ADC
evaluation, typically <1 ps rms jitter
PC running Windows? 98 (2nd edition), Windows 2000,
Windows ME, or Windows XP
PC with a USB 2.0 port recommended (USB 1.1 compatible)
8.
Refer to the instructions included in the respective ADC
data sheet found at www.analog.com/FIFO for more
information about connecting the ADC evaluation board’s
power supply and other requirements. After verification of
power supply connections, apply power to the ADC
evaluation board and check the voltage levels on the ADC
board to make sure they are correct.
Easy Start Steps
9.
Make sure the evaluation boards are powered on before
Important Note
Administrative rights for the Windows operating systems are
needed during the entire easy start procedure.
Completion of every step before reverting to a normal user
mode is recommended.
connecting the analog input and clock. Connect the
appropriate analog input (which should be filtered with a
band-pass filter) and low jitter clock signal.
10. Refer to the VisualAnalog User Manual at
www.analog.com/FIFO for detailed software operating
instructions.
1.
2.
3.
4.
5.
Install VisualAnalog from the CD provided in the ADC
capture board kit or download the latest version from the
Web. For the latest updates to the software, check the
Analog Devices website at www.analog.com/FIFO .
Connect the ADC capture board to the ADC evaluation
board. If an adapter is required, insert the adapter between
the ADC evaluation board and the ADC capture board.
Connect the provided USB cable to the ADC capture board
and to an available USB port on the computer.
Refer to Table 1 for setting the ADC capture board’s I/O
logic level to match the level coming from the ADC evalua-
tion board. 1.8 V is default; 2.5 V and 3.3 V are jumper
selectable. Most evaluation boards can be used with the
default settings.
The ADC capture board is supplied with a wall mount
switching power supply. Connect the supply end to an ac
wall outlet rated for 100 Vac to 240 Vac at 47 Hz to 63 Hz.
POWER SUPPLIES
The ADC capture board is supplied with a wall mount switch-
ing power supply that provides a 5 V, 3 A maximum output.
Connect the supply to the rated 100 Vac to 240 Vac wall outlet at
47 Hz to 63 Hz. The other end is a 2.1 mm inner diameter jack
that connects to the PCB at J4. On the PC board, the supply is
fused and conditioned before connecting to the regulators that
supply the proper bias to the entire ADC capture board.
CONNECTION AND SETUP
The ADC capture board has two 40-pin connectors (J2 and J3)
that accept two 18-bit channels of parallel CMOS or LVDS
inputs from the ADC (see Figure 2 ). The third 40-pin connector
(J1) is used to pass SPI and other USB/FPGA control signals
across to adjacent ADC evaluation boards that support these
features.
The other end is a 2.1 mm inner diameter jack that connects
to the PCB at J4.
Rev. 0 | Page 4 of 32
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
HSHM-GUIDE-PIN-4 CONN GUIDE PIN 8-32 UNC-2A
HSHM-GUIDE-SOCKET-1 CONN HSHM GUIDE SOCKET 1
HTC-10M FUSEBLOCK 250V FOR 5X20 FUSE UL
HV275C GAS TUBE GDT 3KA 2750V CORE
HVR250P080CFF FUSE RESETTABLE 80MA 60V RADIAL
HVR600P160CFF FUSE RESETTABLE 160MA 60V RADIAL
HW-133-PC44 ADAPTER
HW-133-PC84 ADAPTER
相关代理商/技术参数
HSC-ADC-EVALCZ 制造商:Analog Devices 功能描述:EVALUATION KIT ((NS))
HSC-ADC-EVALDZ 功能描述:数据转换 IC 开发工具 Data Converter Evaluation Platform RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V
HSC-ADC-EVAL-SC 制造商:Analog Devices 功能描述:FIFO BOARD FOR HSC A-D CONVERTERS - Bulk 制造商:Analog Devices 功能描述:EVALUTION KITSINGLE CHANNEL ((NS))
HSC-ADC-FIFO5-INTZ 功能描述:INTERPOSER FOR QUAD/OCTAL ADC RoHS:是 类别:编程器，开发系统 >> 配件 系列:- 标准包装:1 系列:- 附件类型:适配器板 适用于相关产品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
HSC-ADC-FPGA 制造商:Analog Devices 功能描述:Evaluation Board High Speed Deserialization Board 制造商:Analog Devices 功能描述:FPGA BOARD FOR HSC ADCS - Bulk
HSC-ADC-FPGA-4 制造商:Analog Devices 功能描述:BOARD FPGA QUAD LVDS FOR ADC 制造商:Analog Devices 功能描述:FPGA BOARD FOR QUAD ADC'S - Bulk
HSC-ADC-FPGA-8Z 制造商:Analog Devices 功能描述:EVAL KIT FOR HS DESERLIZATION BD (HSDB) - Bulk 制造商:Analog Devices 功能描述:EVALUATION CARD ((NS))
HSC-ADC-FPGA-9229 制造商:Analog Devices 功能描述:TOOLS:DEVELOPMENT BOARDS H/W